Hot News! The IC-7000 received FCC certification on November 15, 2005. FCC ID: AFJ242700. Click link below.
 

ICOM IC-7000 preliminary information! ! ! Part 1

 

Here is some preliminary information from Ueda Radio Ltd. on the newly-announced Icom IC-7000 radio.

Here is a summary. The first part is an interior shot of the IC-7000. How is it? It has become substantially simpler, as compared to the IC-706 MK II G of the  preceding generation. When one compares the IC-7000 to the product of over ten years ago, one will observe immense technological  progress.

Click photos for larger images
Ic7000top.jpg

Note the efficient muffin fan, which exhausts heated air from the interior.

Ic7000back.jpg

This photo shows the underside of the chassis. It is very simple.

 

ICOM IC-7000 preliminary information! ! ! Part 2.

 

Here is some more preliminary information from Ueda Radio Ltd. on the newly-announced Icom IC-7000 radio.

Now, let us take a quick look at some screen images.

Ic7000fa.jpg

This is the start-up image, which is similar to that of the IC-756Pro series. It changes to the operational image in approximately 3 - 4 seconds.

Ic7000g.jpg

The radio is in a state where the band scope is turned to ON. When one compares this to the IC-756Pro series, is the scope activity a little more sluggish perhaps? When the band scope is turned on, it has become a slight matter of concern that a "tap-tap" sound is heard and the received audio is interrupted (due to the scope sampling process). We observed this phenomenon in a prototype unit displayed at Ham Fair. This must be how the IC-7000 works, even in the production version.

Ic7000t.jpg

This picture shows the PA temperature indicator. I believe it is an interesting gimmick.

Ic7000m.jpg

This is the HM-151 microphone (with control keys) for the IC-7000. With this microphone, the user will be able to control IC-7000 functions to some extent.

The above is abbreviated preliminary IC-7000 information. Due to the short time we had to collect data, we have only been able to present a partial picture.

We should have more complete information by the end of September 2005.


box.jpg

It was worth the wait! The first IC-7000 100W radio has arrived today (14 Sept. 2005). Initial stock is limited to one unit. By all means, please come to our [Ueda Musen] store; we will offer a special commemorative price.


gamen.jpg

gamen1.jpg

Here you can see the received television picture on the screen of the new ICOM IC-7000. The antenna which is being used to receive the TV signal is the DIAMOND ANTENNA D-130 Discone Antenna, and the TV image is an NHK educational broadcast. One limited batch of IC-7000's arrived at the store, and sold out completely. The next shipment is expected at the end of this month.


ICOM IC-7000 preliminary information! ! ! Part 3.

This is the third announcement of preliminary information from Ueda Radio Ltd. on the newly-announced IC-7000 radio. This time, we have information about a receive Coverage enhancement. This increases the receive coverage to 30 kHz ~ 199.999 MHz and 400 ~ 470 MHz. Icom will offer the receive frequency coverage update free of charge to customers purchasing the radio.

The next shipment of IC-7000's is scheduled to arrive at our store by the end of September 2005. This is fresh new product information as of 2005/09/21!


New product ICOM IC-7000

As we have anticipated for a long time on this blog, the ICOM IC-7000 will be arriving in quantity tomorrow, 10/1/2005. It was worth the wait.

ic7000g.jpg

(*Photo of IC-7000)

Please come to the store and pick one up!


We are displaying the IC-7000

Here is a regular information update from Ueda Radio Ltd.

The demo model of the new Icom IC-7000 product has arrived, and was worth waiting for. We are planning to display it for a while in the Ueda Radio store. Please stop by at our store this weekend.

We have made arrangements to stock the IC-7000.

Demo.jpg

*IC-7000 demo model

Additional IC-7000 Versions: The IC-7000M (50W rig) and IC-7000S (20W rig) will probably be on sale before the end of this year.

10/08/2005


From the Underground

Look what our sources located - a really cool IC-7000 video!

12/03/2009


The IC-7000 received FCC certification on November 15, 2005. FCC ID: AFJ242700.

11/15/2005


Manual Notch Filter (MNF) Tips

  1. If you "slide" the manual notch filter (MNF) right up to one flank of the IF bandpass filter, it will tend to sharpen up that flank. Now if you place one of the IC-7000's dual MNF's close to each flank of the bandpass filter, it will improve its shape factor.

  2. If you position an MNF on each side of a weak CW signal, you are constructing an incredibly narrow DSP bandpass filter. By moving the 2 MNF's around, you can optimise the filter for the best rejection/ringing or noise bandwidth/ringing trade-off.


Note on Compression

  • The directions given in the instruction manual regarding the setting of the compression threshold are incorrect. On page 88 of the USA released Instruction Manual, the instructions state: "NOTE: When the ALC meter peaks below the ALC zone, your transmitted voice may be distorted. Adjust 'COMP LEVEL' so that the ALC meter peaks above the ALC zone." This is precisely the opposite of how the levels should be set! (Contributed by Paul Marbourg, WN7T)

  • In SSB mode, set 'COMP LEVEL' for approx. 6 dB compression on voice peaks.

02/25/2006


VHF/UHF VSWR Protection

 
VHF PA Reflectometer Circuit. Image courtesy Icom Inc.   UHF PA Reflectometer Circuit. Image courtesy Icom Inc.
VHF PA Reflectometer Circuit   UHF PA Reflectometer Circuit
  • Although there is no VSWR indication on the 2m or 70cm bands, the VHF and UHF PA stages are still mismatch-protected.

  • Reflectometers in the VHF and UHF PA output lines will protect the PA devices in the event of a mismatch. L410, D401 and D404 in the UHF PA, and L502, D501 and D504 in the VHF PA respectively, constitute simple reflectometers. (Refer to partial schematics above.)

  • To quote the IC-7000 service manual (p. 3-7): The VHF/UHF APC detector circuits (PA unit; D501, D504, D401, D404) detect the forward and reflection signals and convert into DC voltages. The converted DC voltages are combined and applied to the ALC amplifier (pins 1, 2) as "VUFOR" voltage.

  • Thus, it will be seen that even though the IC-7000 VSWR indicator does not operate on the 2m and 70cm bands, the VHF and UHF PA's are nonetheless protected. A sudden drop in Po will indicate a high VSWR condition.

05/17/2006


IC-7000 TX Driver Stage: Current and Heat

 
IC-7000 Transmitter Driver Schematic. Image courtesy Icom Inc.
IC-7000 Transmitter Driver Schematic

It has been observed that the IC-7000's transmit standing current is approx. 4A in SSB mode, without audio input. Users have also reported that the radio runs "quite warm".

The TX driver stage, Q504 (DRIVER Unit), is a single-ended PD55015 MOSFET operating in Class A with Vdd = 13.8V (nom.) The driver alignment procedure (IC-7000 Service Manual, Sec. 4-4) specifies 1A driver standing current. If we assume that the HF/6m PA stage has 15dB power gain, Q504 must deliver 3W for 100W output. As the efficiency of a class A amplifier is approx. 20%, the DC input to this stage will be about 15W whenever the transmitter is keyed. This equates to 1.1A at 13.8V - about 25% of the 4A standing current noted above. In addition, Q504 will dissipate approx. 15W without drive - a significant contribution to the radio's thermal budget.

(Note: A single-ended driver was selected in the interests of circuit simplicity and PCB real-estate conservation.  The advantage of this topology is that a single driver stage can be common to HF, 6m, 2m and 70cm. As this stage is broadbanded, it must be operated in Class A to ensure adequate harmonic suppression. The Class-A amplifier is inefficient, as its conduction angle is 360º. It will therefore draw significantly more DC input current for a given RF output than a Class-AB amplifier. In contrast to Class AB, the Class-A amplifier will also dissipate 100% of its DC input power when not driven.)

06/18/2006


Issues in IC-7000 Manpack Operation

The IC-7000 is not the optimum choice for manpack service. Its standing current consumption on receive/standby is 1.3A (vs. 0.3A for the IC-703). I would estimate that it draws approx. 8A at 5W output, and 11A at 10W output. The TX driver stage is Class A, and dissipates at least 15W key-down with or without drive.

You will need a battery-wallah to wheel a trolley-acc behind you whilst you are trudging through the wilds with your radio on your back (or at least a very large dog by your side, with battery-laden saddlebags over his back.) The advantage of a human (as opposed to a canine) assistant is that he can also brew you a cuppa during breaks or poor prop! In addition, a human can work the pedal-generator when the battery gets low.

During WW2, the battery-wallah was always recognisable as the member of a 3-man Royal Signals infantry radio team who had the acid-burn holes in his trouser-cuffs.

Typical battery-wallah. Click for larger picture. Photo courtesy G0GSF.

03/27/2007


All information on this page through October 2005 courtesy Ueda Musen Staff Voice. Japanese-language page. Copyright © 2005 Ueda Musen K.K. (Ueda Radio Ltd.)

Translation and page creation by A. Farson VA7OJ/AB4OJ.

Read my IC-7000 Evaluation Trip Report (PDF).

IC-7000 Review by Phil Salas AD5X (PDF).

View a large picture of the IC-7000 (image courtesy Icom UK).

View a video of the W8LX DSP IF Filter Test, by Scott N7SS.

View a selection of IC-7000 screenshots (courtesy Icom America)

Download the IC-7000 TVRO/Mars Mod.

Join the IC-7000 Group

New Trends in Front End & LO Design

IC-7000 "Hidden Menu"?

Scott, N7SS' IC-7000 X-Ray Views

Scott, N7SS' IC-7000 Frequently Asked Questions (PDF).

Bob Nagy AB5N's IC-7000 Microphone Page (with audio clips for various menu settings)

Last updated: 18 October, 2019.