This  multiband  antenna  covers  the  80,  40,  30,  20,  17,  15,  12,  10  and  6  Mx  Amateur  bands.  Multiband  operation  is  achieved  by  use  of  300  ohm  balanced  line  fed  to  an  antenna  tuner.  This  loop  antenna  needs  to  be  run  in  the  horizontal  plane.  ie.  parallel  to  the  ground.  The  formula  used  to  determine  fundamental  frequency  wire  length  is  :-   Length (feet)  =  1005 / Frequency (Mhz).  I  operate  mainly  CW,  so  I  cut  the  wire  length,  for  the  80  Mx  band,  to  88  metres  (287  feet).  If  you  operate  SSB,  the  length  of  the  wire  will  need  to  be  shorter,  in  accordance  with  the  above  formula.  I  used  high  tensile  fencing  wire  in  the  shape  of  a  square  supported  by  four  trees.  The  winds  here  can  be  ferocious  so  strong  wire  is  needed  even  though  radiation  efficiency  will  be  compromised  by  using  fencing  wire.  Since  our  HF  bands  are  harmonically  related,  this  length  of  wire  covers  all  HF  bands  from  80  mx  up  to  10  mx,  including  the  WARC  bands.  If  the  wire  is  cut  for  the  40  metre  band,  about  44  metres  of  wire  or  slightly  less,  the  antenna  can  also  be  used  on  all  the  higher  HF  bands.  Of  course,  a  perfect  square  of  wire  is  far  from  achievable  here.  A  circle  is  theoretically  ideal  but  even  a  triangle  of  wire  will  work.  The  feedpoint  of  the  antenna  can  be  placed  any  where  but  I  positioned  it  about  two  feet  from  the  corner.  The  diagram  below  gives  you  some  idea  of  the  layout.

 

 

 
 
 

 

This  image  shows  one  of  the  trees  to  which  the  wire  is  attached.
 
 

 

 

 

The  trees  at  this  location  are  not  very  high  so  the  average  height  of  the  antenna  is  only  about  20  feet  or  so.
 
 

 

 

 

The  feedpoint  can  be  seen  on  the  left.  I  used  15  metres  of  300  ohm  ladder  line
which  can  be  purchased  in  various  lengths  from  DXEngineering.

 

 
 
 
 
 

 

 

 

A  perspex  block  and  splicing  tape  reduce  the  strain  on  the  feedline  at  the  feed  point.
Rubber  splicing  tape  can  also  be  purchased  from  DXEngineering.
 

 

 

 

One  'corner'  of  the  antenna.
 
 
 

 

 

The  operating  position  located  in  an  old  caravan  which  is  solar  powered.  The  tuner  can  be  seen  on  the
left.  The  radio  is  the  Yaesu  FT-450.
 
 

 

 

The  Tuner  -  MFJ-969.
 
Even  at  a  low  height,  this  antenna  performs  very  well.  Surprisingly  so.  One  of  its  attributes  is  that  it  is  quiet  on  receive.  Another  is  that  it  has  many  radiation  lobes  and  therefore  works  well  in  several  directions.  It  costs  little  to  build.  It's  straight  forward  to  construct  and  fairly  easy  to  erect,  although  in  my  case  I  had  a  sore  shoulder  after  throwing  the  lines  up  into  the  trees.  This  multiband  horizontal  loop  may  be  the  antenna  you  are  looking  for. 

If you would like to view or save this page without any of the links shown below, Click here.

 

Also,  Ed,  VK2JI  has  an  interesting  article  about  his  40  Mx  Loop  -  click here.
 

 

                 
 

 

                               

80 Mx Loop

Vee Beam

Hustler Vertical

20 Foot Tower

Cubex Quad

 

 

.